Sargent 988 Surface Bolt Kit Manuel d'utilisateur télécharger pdf

A7426E

CAUTION: BEFORE STARTING

• DOOR SHOULD BE FITTED AND HUNG

• CHECK BOX LABEL FOR HAND AND SIZE OF EXIT DEVICE

AVAILABLE STOCK LENGTHS

LENGTH E 32" DOOR. CAN BE CUT TO FIT 24" DOOR.

LENGTH F 36" DOOR. CAN BE CUT TO FIT 33" DOOR.

LENGTH G 48" DOOR. CAN BE CUT TO FIT 43" DOOR.

LENGTH J 42" DOOR. CAN BE CUT TO FIT 37" DOOR.

Lift

lever

Lift

lever

2-1/4" long pin

Top case

Retractor

Rail assembly

Top rod

Guide

Bottom

rod

Adjustment

Bottom

case

Vertical reference line

of chassis)

Vertical reference line

of chassis)

Horizontal reference line

of chassis and rail assembly)

Horizontal reference line

of chassis and rail assembly)

Horizontal reference line

of chassis and rail assembly)

Vertical reference line

of chassis)

US PATENT NO. 268003

CANADIAN PATENT NO. RD1981

ALL 12-3727 SERIES EXIT DEVICES

ARE HANDED AND REVERSIBLE. NORMALLY ASSEMBLED FOR

A LEFT HAND REVERSE BEVEL DOOR AT THE FACTORY.

TO CHANGE HAND OF 12-3727 EXIT DEVICE:

1. USE 2-1/4" PIN (SUPPLIED IN SCREW PACK) TO PUSH OUT

LIFT LEVER PIN

2. REMOVE LIFT LEVER. INVERT AND REASSEMBLE WITH LIFT

LEVER PIN AS SHOWN

THIS EXIT DEVICE IS HANDED

Door stop

Top case

template

TAPE TEMPLATES ON INSIDE OF DOOR ALONG

REFERENCE LINES WITH SUPPLIED TAPE

IF DOOR ALREADY HAS ANSI DOOR PREP (161 CUT-OUT) OR HAS

2-1/8" DIA. HOLE AT 2-3/4" BACKSET, POSITION TEMPLATE OVER EXISTING

HOLE AND SPOT AND DRILL HOLES

DETERMINE DIMENSION "A"

- IF LOCK STILE IS APPROX. 4 1/2"

WIDE OR WIDER, DIM. A=2 3/4"

- IF LOCK STILE IS LESS THAN 4 1/2"

WIDE, DIM. A = 1/2 OF THE VISIBLE

WIDTH OF THE LOCK STILE (WHEN

DOOR IS CLOSED AGAINST STOP)

FINISHED FLOOR

Refer to template to locate

horizontal reference line

RIGHT HAND

REVERSE BEVEL

LEFT HAND

REVERSE BEVEL

OUT

Bottom

cover

Center chassis

assembly

Top cover

Adjustment pin

Lockdown

button

“Lockdown key”

To operate:

Depress pushrail; insert hex

key and turn

Mounting plate

End cap

Door

Dim “A”

PREPARE DOOR

APPLY HARDWARE

ANSI A156.2 series cross bore hole

when knob rim or lever handle trim

is used

FOR LEVER TRIM APPLICATIONS

SEE SEPARATE INSTRUCTION SHEET PACKED WITH TRIM

41"

INSTRUCTIONS FOR INSTALLING

12-3727 / 12-NB3727 SERIES

VERTICAL ROD EXIT DEVICE.

FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com

NOTE: FOR EXIT ONLY APPLICATIONS

REMOVE AND DISCARD CAM FROM

CENTER CHASSIS FOR FLUSH

MOUNTING. ATTACH CHASSIS WITH

FOUR (4) #10 WOOD OR MACHINE

SCREWS

Cam

Center

chassis

cam

MARK VERTICAL AND HORIZONTAL

REFERENCE LINES ON DOOR

of Sargent Manufacturing Company is prohibited.

1 2

Résumé du contenu

Page 1 - VERTICAL ROD EXIT DEVICE

A7426ECAUTION: BEFORE STARTING• DOOR SHOULD BE FITTED AND HUNG• CHECK BOX LABEL FOR HAND AND SIZE OF EXIT DEVICEAVAILABLE STOCK LENGTHSLENGTH E 32&

Page 2

ATTACH COVER TO CHASSISWITH (4) #8 TRUSS HEADMACHINE SCREWS• CHECK BOX LABELDEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTOCHASSIS. LEVEL RAIL AND

Commentaires sur ces manuels

Pas de commentaire

Sargent 988 Surface Bolt Kit Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Sargent 988 Surface Bolt Kit. SARGENT 988 Surface Bolt Kit User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Sargent 988 Surface Bolt Kit